Tank & Mixer Packages
Pre-Engineered - Ready to Use

Tank and mixer packages are designed, engineered and built to provide long, trouble free service in blending and mixing applications. Our pre-engineered packages are used to blend liquids, suspend or dissolve solids, and dispense immiscible liquids in a wide variety of industrial applications. Blend and mix paints, varnishes, polymers, textile sizes and dyes, pharmaceuticals and countless other materials from 1 to 2,000 CPS viscosity.

We offer Neptune Mixers in our pre-engineered packages

Our tank and mixer packages consist of a heavy-duty molded polyethylene tank (capacity and tank style determined by your application) a steel stand with a mixer support bar or a floor mounted bar and the appropriate NEPTUNE MIXER. See chart for mixer selection.

MIXER SELECTION CHART

Our chart is intended to furnish basic guidelines for selecting the proper mixer to provide a mild blending of liquids of various viscosities in different size tanks. This information is based on an approximate 30 minute mix-blend time for two liquids when both liquids are already in the tank. Mixing times can be shortened if one liquid is added while the first liquid is already being mixed. Powders should always be added while mixer is running.
VISCOSITY
CPS
TANKS UP
TO
50 GAL
TANKS UP
TO
100 GAL
TANKS UP
TO
200 GAL
TANKS UP
TO
500 GAL
TANKS UP
TO
1,000 GAL
  Mixer Part # Mixer Part # Mixer Part # Mixer Part # Mixer Part #
= or < 1 CTBN 10 CTBN 10 CTBN 10 CTBN 10 CTAG 10
= or < 100 CTBN 10 CTBN 10 CTBN 20 CTAG 10 CTAG 10
= or < 300 CTBN 10 CTBN 20 CTAG 10 CTAG 10 CTAG 20
= or < 500 CTBN 20 CTAG 10 CTAG 10 CTAG 10 CTAG 30
= or < 1000 CTBN 20 CTAG 10 CTAG 20 CTAG 20 CTAG 40
= or < 2000 CTAG 10 CTAG 10 CTAG 30 CTAG 30 CTAG 51
Optimum mixing will be achieved when the mixer is angled from the tank wall. "Angling-Off" center is preferred when good material turnover is required, as in mixing a slurry. "Angling-On" center is desirable for a gentle mixing action or when vortexing must be minimized. Improper mounting of a mixer can greatly lessen mixing efficiency, cause vibration, and possibly damage the mixer. See bottom of page for illustrations.

NEPTUNE MIXER FEATURES:
CTBN 10 & 20 Models

  • Coupling fully enclosed for safety.
  • Direct drive-small batch mixing.
  • 316 S.S. Shafts and propellers.
  • Clamp adjusts to any angle.

CTAG 10, 20, 30, 40 & 51 Models

  • 350 RPM gear-driven. 316 S.S. shafts and propellers.
  • 1.0 pitch ratio marine propellers.
  • Flow co-efficient and power consumption characteristics equal to those of the best hydro foil impeller designs.
  • Adjustable shaft angle to achieve optimum mixing for various processing needs.
  • Motors are enclosed, fan cooled (TEFC.
  • Explosion-proof motor available. Permanent grease gears.
  • Mixer shaft bearings are permanently lubricated.
  • Available with air motors for use in flammable , or explosion-proof environments.
FLAT BOTTOM TANKS AND STANDS SPECIFICATIONS

TANK
CAPACITY
(GAL)
SIZE
DIA. x HT.
(IN.)
TANK
PART #
AM
STAND
PART #
AN FLOOR
MOUNTED
PART #
30 18 x 29 TC1829AA TC1829AM TC1829AN
55 22 x 36 TC2236AA TC2236AM TC2236AN
100 28 x 42 TC2842AA TC2842AM TC2842AN
150 31 x 48 TC3148AA TC3148AM TC3148AN
200 36 x 48 TC3648AA TC3648AM TC3648AN
275 42 x 48 TC4248AA TC4248AM TC4248AN
360 48 x 48 TC4848AA TC4848AM TC4848AN
500 52 x 60 TC5260AA TC5260AM TC5260AN
700 55 x 70 TC5570AA TC5570AM TC5570AN
1000 66 x 72 TC6672AA TC6672AM TC6672AN


CONE BOTTOM TANKS AND STANDS SPECIFICATIONS

TANK
CAPACITY
(GAL)
 SIZE
DIA. x HT.
(IN.)
TANK
PART #		 CM STAND WITH
MIXER MOUNT BAR
PART #
30 18 x 29 TC1829CA TC1829CM
55 22 x 36 TC2236CA TC2236CM
100 30 x 36 TC3036CA TC3036CM
250 42 x 46 TC4246CA TC4246CM
500 52 x 64 TC5264CA TC5264CM
750 62 x 58 TC6258CA TC6258CM
1000 66 x 72 TC6672CA TC6672CM

Hinge covers available for all tanks.
MIXER SPECIFICATIONS

MIXER
PART #		 MOTOR
SPECS		 SHAFT
LENGTH		 LENGTH
OF GEAR
DRIVE & MOTOR		 TOTAL
LENGTH		 PROPELLER SHAFT
CTBN 10 1/4 H.P. 115/230 30" 14" * 44" 4" 1/2"
CTBN 20 1/3 H.P. 115/230 32" 14" * 46" 4" 1/2"
CTAG 10 1/4 H.P. 115/230 48" 21 1/16" 69 1/16" 8" 3/4"
CTAG 20 1/3 H.P. 115/230 48" 21 5/8" 69 5/8" 10" 3/4"
CTAG 30 1/2 H.P. 115/230 48" 22 1/2" 70 1/2" 12" 3/4"
CTAG 40 3/4 H.P. 115/230 60" 22 3/4" 82 3/4" 13" 3/4"
CTAG 51 1 H.P. 230/460 60" 22 3/8" 82 3/8" 14" 1"

* Direct drive
Shaft lengths can be adjusted.

NOTE: More sizes are available, contact sales office for details.


Angling the portable mixer off center is the position recommended
for rapid turnover of tank contents and good bottom washing.


On center angling will produce good mixing with minimum vortexing.
Tank contents turn over thoroughly but gently.

About Us | Site Map |Contact Us | ©2006 Hazmat Chemical Storage, Inc.